- need help 17* hpop fittings leaking
- Knock after injector rebuild
- Tranny temp. gauge
- Simple question about injectors
- electronic guru's ?
- Turbo Time #2
- Rollover valve
- Home made air breather
- magnet tranny cooling fins
- rear leaf springs...
- lowering components
- Starter motor... AGAIN !!!
- Anybody have ideas for a stereo system?
- Oil Pan Seal Question
- cup holder
- PCM code info.
- Tranny sticking in first...some times
- Questions about Jody's Tuning
- Tranny woes
- converting from lift blocks to lift springs... can I use chunks of spring to get extra lift
- Part number/Proper Name Question
- DIY Tymar = Definitely a must-do
- Steering staiblizer
- Replace transmission before mod?
- superduty starter
- Anybody else lifting the head with Stage ones, D66 , ARP headstuds and Cometic gaskets?
- Intercooler install?
- Axle wrap...
- HPX Line Install Frustration
- best upgrades?
- Installing a fuel system
- Multiple MISSES at idle, fine in drive?
- 1997 Ford F350 Front Track Bar
- 1997 F350--Looking for a certain Service Body--Help
- Crossmembers
- Blackbirds or TSM Disc brake kit ?
- High pressure oil pump upgrade
- what yr did econo vans have disk?
- MAP question(s)...
- air bags
- Chip question
- I NEED RUBBER!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- About overload springs?
- SRW to DRW
- DIY injectors
- I need a favor trim measurement
- Jack
- hpo line
- help smokes loss power
- 7.3 intercooler
- overhead shelf for 95's?
- Ceramic coatings and Bolts?
- **Gripes about the rules and administration.....**
- Boost Gauge Location After Intercooler Install ?
- Turbo Upgrade
- Superduty rear springs
- where are your EGTs at?
- super duty springs?
- Meth/H20 Inj.? or Innercool
- Dynamat Hood Liner
- Measurements please on RSK and stock springs
- short bed to long bed
- Chip
- gauges
- Overhead dome light
- What diameter foam backer rod for door seals?
- air filters... which one?
- I give up searching, need link to TC lock up switch
- Dana 60 DRW to SRW
- Headlight bulb
- Pictures of front ranch hand full replacement?
- Lift blocks- tapered or straight?
- Cheap power adders?
- Love the Tymar intake
- Stud question, and smoke video
- Drop Bracket ????
- Air filters
- Transfer Case
- Cackle????
- 1997 PSD Turbo Upgrade
- obd1
- is 3'' exhaust killing performance ???
- what is a down pipe?
- Donor parts for TTB upgrade
- injector upgrade questions?????
- Aftermarket hood
- OBS with 22.5's or 19.5"s Floaters??
- freshening up a PSD
- gtp38r turbo onto obs
- Do I need high press oil crossover with HPOP upgrade?
- skyjacker 2.5 inch leveling kit
- HPOP Choices
- Edge programer
- wildman chip
- 6.0L Tranny Cooler into a 97?
- 1st 1/4 Mile
- AC code Injectors?
- 1995 centurion conversion
- Rumble in cab after downpipe install
- 4 inch exhaust installation
- Newb!
- Tymar Exhaust??
- stainless brake hoses
- Bigger injectors for towing?
- Downgrade Premium Audio to Basic Audio
- swapping buckets into a 94.5 standard cab - anyone done it?
- tranny options
- Dana 80
- Trying 8oz of Redline two-stroke oil per tank.
- Getting a lift...Have questions.
- 95 TURBO ISSUE
- No start with new chip, HELP
- Routing wirre for chip Help ASAP
- trans guru ? just rebuilt problems
- E4OD Shifting problems.
- IC install
- My truck NEEDS to ride better.
- Superchips MicroTuner ?'s
- 00' powerstroke or 04' cummins intercooler?
- h2e exhaust housing
- Bumpers
- CAT - ELC ?
- Seat covers
- shocks
- shimming the fpr question
- best chip or tuner
- limited slip
- real oil pressure gauge
- Radiator \ Intercooler Install
- rear disc brakes and aluminum diff cover installed!
- rear leaf shackle F250 1997, differant than F250 2002 SD?
- egt guage probe question
- 4 inch springs in the front
- 3x4 down pipe/ up pipe clearance
- Dodge IC, will it fit?
- cold driveability problem--94 stroke
- 03 6,0 ltr intercooler into a 1997 F-250 with a 7.3ltr engine
- injectors are in!!!!
- D60 swap quest.
- Need pics of flat beds on OBS trucks
- glow plugs how too, any one got any instrutions
- Change Turbo wheel on truck?
- Just installed DP-tuner chip...
- Edge Evo/Edge E-Z Stack
- Please HELP!!!! IDM Code
- I need a torque converter
- D60 Ubolt Bracket
- Trans temp sensor location
- finally getting some money for power upgrades.
- MBRP 4" or Diamond Eye 5"?