Diesel Forum - TheDieselStop.com - View Profile: DENNY

DENNY DENNY is offline

Senior Member

  About Me

  • About DENNY
    Location
    Chugiak Alaska
    Interests
    RUNNING, CAMPING, WOODWORK, TRUCKS,
    Occupation
    PHYSICIAN ASSISTANT, USAF RET
  • Signature
    Early 1999 F350 AUTO 4x4 CC LB DRW 4.10 6.0 trans cooler, Front hitch, 2,000 hubs/ brakes, Bilstein shocks/steering stabilizer, Diesel site coolant filter 203 thermostat, EBV delete, new O-rings, new Oil cooler, RIFF RAFF FRX, Glow plug led, Pillar gauges, Lighted cupholder, Painless wiring fuze block, Harpoon/hutch mods, Removed axle blocks. Air bags, 5 wheel hitch, In bed 7 pin plug. Spare tire key delete. KLHANSEN on speed dial. 75,000 as of May 2019

  Statistics

Total Posts
General Information
  • Last Activity: Today 12:01 AM
  • Join Date: 04-27-1999
  • Referrals: 0

  Mentions

12-18-2018
06:28 AM - HeavyAssault mentioned DENNY in post Did dealer fry my front diff during delivery?
...K, drive out. DENNY: Since this is a 20...
11-09-2017
04:14 PM - Texas_proud77836 mentioned DENNY in post Front end jerking feeling
DENNY that?s something I d...
10-02-2017
06:26 AM - HeavyAssault mentioned DENNY in post Bouncy Ride
DENNY: By that table my f...
09-19-2017
12:05 PM - QuercusRubra mentioned DENNY in post Where to splice in for power to extra gauges?
[quote=DENNY;4481545]I usually ju...
11-27-2016
08:26 PM - Texas_proud77836 mentioned DENNY in post Cold start, a little advice please
... injectors. DENNY if you read the earl...
04:36 PM - Texas_proud77836 mentioned DENNY in post Cold start, a little advice please
DENNY... I want to do the ...

  Quotes

10-18-2019
10:18 AM - twglace quoted DENNY in post 500 miles post injector job madness
... do it a time or 2. DENNY Will do, thanks.
10-17-2019
11:33 PM - ArcticDriver quoted DENNY in post proud ford owner
...e the codes pulled. DENNY Did you say that co...
09:02 AM - Big Horn quoted DENNY in post Flush & Change Power Steering Fluid
...his is a good one. DENNY Thanks Denny, I do...
07:18 AM - twglace quoted DENNY in post 500 miles post injector job madness
... side or the other. DENNY Drove golden for 5...
10-16-2019
01:30 PM - twglace quoted DENNY in post 500 miles post injector job madness
...ly not one of them. DENNY What is “sig ...
10-14-2019
06:56 PM - srh240 quoted DENNY in post Want more power for towing
...e tranny holds up. DENNY I am fine with le...
10-11-2019
12:50 PM - Turbo X quoted DENNY in post High Silicons in oil
...gs to think about. DENNY Correct, I only t...
10-06-2019
08:31 PM - badbart quoted DENNY in post 2002 F-250 30+mpg?!
...an overdrive unit? DENNY My old 97 would g...
09-29-2019
11:16 PM - Turbo X quoted DENNY in post High Silicons in oil
...longer than a year. DENNY My truck was purcha...
09-26-2019
09:45 PM - plscott1951 quoted DENNY in post Newbee checking in
...xas then Alaska. DENNYThank you, I'll defin...
09-22-2019
10:38 PM - ArcticDriver quoted DENNY in post Tire suggestions for F350
...ow than a wide one. DENNY Denny, The old rule...
09-20-2019
04:57 PM - rv6a quoted DENNY in post Pulling in the mountains question
... hill with a load. DENNY After replacing m...
08-30-2019
09:06 AM - RT quoted DENNY in post Diesel in my oil
...me how to do that. DENNY Yep - Kevin came ...
08-29-2019
12:13 PM - RT quoted DENNY in post Diesel in my oil
...on when I do it. DENNY Isn't it fun scru...
08-28-2019
10:21 PM - bigb quoted DENNY in post Towing Scenario & Question:
...s will answer that. DENNY I'm not a smart guy...
07-07-2019
08:59 AM - Big Horn quoted DENNY in post Calipers and Brake System
... usually does!!! DENNY :surprise: Lm...
07-06-2019
05:09 PM - Big Horn quoted DENNY in post Calipers and Brake System
...indle bearing also. DENNY While I’ve g...
07-02-2019
11:20 PM - DAH7 quoted DENNY in post I bought a 7.3L! '1996 F250 with 211k miles
... valve cover bolts DENNY Thanks Denny, i'l...
06-29-2019
01:42 PM - Barchetta quoted DENNY in post air separator to mitigate pickup issues?
...ith the Air-Dog. DENNY Im aware of the 1...
05-18-2019
05:52 PM - oldrebuiltdodge quoted DENNY in post How to source a new vacuum resevoir/canister?
...pipe and end caps. DENNY Use thread adapters...

  Feedback Score

iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback
  Past
Month
Past
6 Months
Past
12 Months
Positive Positive 0 0 0
Neutral Neutral 0 0 0
Negative Negative 0 0 0
 
For the best viewing experience please update your browser to Google Chrome