Diesel Forum - TheDieselStop.com - Reply to Topic
7.3L IDI Diesels (Not Power Strokes) Technical discussion of topics related to vehicles powered by the 7.3 Liter In-Direct Injection Navistar engines.

Thread: Fuel heater O rings Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Diesel Forum - TheDieselStop.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
01-27-2018 12:33 AM
COTom1 Weird because all of the Pictures of the F2TZ9J294A Fuel heater show O-rings! That may have changed with later models. Where Ford had a better Idea and put the heater rear center of the engine.
01-26-2018 09:34 AM
LMJD Found quite a few pics of it on Google going by that IH part number and it does appear to be a O-ring rather than a quad ring (square sided). Mine had a cracked plastic terminal due to age and heat and FYI I found out later the heater ass'y is 1/2 the price from IH truck dealership than from my friendly Ford dealer. It came in a typical FoMoCo blue/white box but was in an IH wrapper with the IH part number on the wrapper.
01-26-2018 01:06 AM
COTom1 Found this on a different form go to IH and ask for part # 1811053C1 not sure what they run but I found 1 on Ebay for about $10.00. Kind of Pricey but beats $130 for a new Heater Assembly
04-19-2016 01:12 PM
Bill1013
Quote:
Originally Posted by Xeonpony View Post
Useless till it gets cold out!
According to Fords manual, the key has to be left on for 5 minutes prior to starting to make the filter heater to heat the fuel enough to be effective, then key OFF then ON to cycle the glow plugs, then start.

Many many have deleted the heater as I've said for the reason the damn things leak and air intrusion.

Your truck, but do as you want.

The PSD's have the heater at the bottom of the fuel bowl, higher wattage, more effective.
04-19-2016 08:12 AM
LMJD
Quote:
Originally Posted by chuckster57 View Post
O ring may have been round, being installed for 24+ yrs may have made it look square. I know I couldn't get a round one in, but once I squared one or three off, I got it to fit snug.
When this came up before I thought I saved my old leaking heater, but when I looked for it evidently I'd trashed it. And my O-rings weren't leaking, I could have measured them and maybe ID'd them.
04-19-2016 07:54 AM
Xeonpony Useless till it gets cold out!
04-18-2016 11:10 PM
Bill1013 Just do away with the heater, there useless. Drill and tap the hole for a 1/2" NPT pipe plug.
04-18-2016 09:16 PM
chuckster57 O ring may have been round, being installed for 24+ yrs may have made it look square. I know I couldn't get a round one in, but once I squared one or three off, I got it to fit snug.
04-18-2016 08:17 AM
LMJD I used to reseal all types of dozer hyd rams, banks of control valves in graders, etc, and I'm sure not disagreeing with Chuckster, but most of the time the round O-rings get mis-shaped over time and are somewhat flattened with age. Any chance that's the case here, Chuck? My heater plastic terminal cracked with age so I replaced the complete ass'y about 6 years ago but I can't remember if it had quad rings (square sided) or regular O-rings.
04-17-2016 03:01 PM
chuckster57 Yeah. I wasted a few O rings making it right.
04-17-2016 11:37 AM
Xeonpony High quality lubricant and some force does wonders
04-16-2016 05:06 PM
chuckster57 I don't remember what size I used, but yeah I squared off the outer edge. When I took my old one out it looked Ike it had a square profile not round.
04-16-2016 04:36 PM
Paul916 I'm not sure I understand when you say you used a bench grinder to square it off. Are you talking about the o ring. You shaved off the outer part of the o-ring? And what size o-ring did you use?
04-16-2016 02:33 PM
chuckster57 When I did mine, I used a Vinton O ring, and using a bench grinders. made the outer surface square. Hasn't leaked since '08.
04-16-2016 01:33 PM
Paul916
Fuel heater O rings

I have a 1990 7.3 with leaking around the fuel heater and leaking air back into the system. I disassembled the unit and as another post suggested using a 114 o ring which according to my set measures 5/8 ID, 13/16 OD and 3/32 thick. This size was too big and would not fit back together. So I used a size down, 016 o ring 5/8 ID, 3/4 OD, and 1/16 thick. This size was too small and it slid right but doesn't seal. I read on one post of using a A018 o ring, but I have not been able to find that size. Does anyone know what the dimensions are of an A018 o ring are? Also is there a metric size that would work instead for making this repair? Looking for suggestions Thanks..

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome