Diesel Forum - TheDieselStop.com - Search Results
Advanced Search
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Search: Posts Made By: drgrcr
Forum: '99 & up 7.3L Power Stroke Engine and Drivetrain   11-21-2016, 10:47 AM
Replies: 5
Views: 1,620
Posted By drgrcr
Yeah, low fuel pressure sounds right. They are...

Yeah, low fuel pressure sounds right.
They are Alliant o-rings.
Now I just have to capture it again to check fuel pressure.
This truck crosses the Mohave Desert every day overloaded 5k to 10k, ...
Forum: '99 & up 7.3L Power Stroke Engine and Drivetrain   11-20-2016, 10:48 PM
Replies: 5
Views: 1,620
Posted By drgrcr
2000 F350 SD 7.3L Inector o-rings

Post a question to forum, I do all the mechanical repair on 00 SD that is used as a transport truck. It hauls enclosed trailer on a fifth wheel trailer. This vehicle is loaded to 25 to 30k every...
Forum: Power Strokes 1994-1997 General   10-14-2015, 01:11 AM
Replies: 13
Views: 939
Posted By drgrcr
Turbo is coming off in the morning. Owner...

Turbo is coming off in the morning.
Owner supplied a turbo of a known good truck. Will disassemble removed turbo and post pictures.
All boots, and exhaust pipes are tight.
Forum: Power Strokes 1994-1997 General   10-14-2015, 01:06 AM
Replies: 13
Views: 939
Posted By drgrcr
No change.

No change.
Forum: Power Strokes 1994-1997 General   10-13-2015, 04:22 PM
Replies: 13
Views: 939
Posted By drgrcr
Replaced the line and removed the checked the...

Replaced the line and removed the checked the connection fitting at the manifold.
Thx
Forum: Power Strokes 1994-1997 General   10-13-2015, 12:47 AM
Replies: 13
Views: 939
Posted By drgrcr
Swapped gauge, same results Unplugged Map...

Swapped gauge, same results

Unplugged Map sensor, no change

Not sure if unplugging Baro sensor will put vehicle into set parameter?
Forum: Power Strokes 1994-1997 General   10-12-2015, 12:21 AM
Replies: 13
Views: 939
Posted By drgrcr
Boost is being measured with a psi gauge T into...

Boost is being measured with a psi gauge T into the map sensor line. WOT accels engine rpm 3k upshifts to second run it on up to 35-40 mph then abort the run due to zero boost, verified gauge. no...
Forum: Power Strokes 1994-1997 General   10-11-2015, 12:54 PM
Replies: 13
Views: 939
Posted By drgrcr
Measured at idle to WOT, no pressure while...

Measured at idle to WOT, no pressure while driving, not static.
No boost.
Forum: Power Strokes 1994-1997 General   10-11-2015, 03:41 AM
Replies: 13
Views: 939
Posted By drgrcr
'96 F250 No Boost

Working on a friends 96 PS engine has no boost. Measuring boost at the map sensor line.
Did find the EBP valve stuck closed. The throttle blade has been removed. Still no boost.
ECM has been...
Forum: 6.0L Power Stroke Engine and Drivetrain   11-04-2012, 11:01 AM
Replies: 58
Views: 23,830
Posted By drgrcr
Are any of them made in the US?

Are any of them made in the US?
Forum: 6.0L Power Stroke Engine and Drivetrain   11-01-2012, 05:29 PM
Replies: 58
Views: 23,830
Posted By drgrcr
Filters and oil, kinda like talking about...

Filters and oil, kinda like talking about religion and politics.....

But, i have seen the Fram and Wix filter display at O-Riely's no doubt about it Wix is a much better filter
Forum: '99 & up 7.3L Power Stroke Engine and Drivetrain   03-26-2011, 04:33 PM
Replies: 3
Views: 13,749
Posted By drgrcr
Found the nut off that holds the IPR solenoid the...

Found the nut off that holds the IPR solenoid the the valve allowing the solenoid to float causing all kinds of problems. assembled the IPR and drove the truck for 45 minutes ran great. Started it...
Forum: '99 & up 7.3L Power Stroke Engine and Drivetrain   03-25-2011, 07:46 PM
Replies: 3
Views: 13,749
Posted By drgrcr
Leaking injector o-rings or a bad HPOP?

Hi yall, I have been working on a 99 7.3 that has a stalling long crank time after the oil temp gets above 130' f, I am using a Ford NGS to monitor oil temp, ICP pressure and ICP duty cycle. Have...
Forum: 6.0L Power Stroke Engine and Drivetrain   02-08-2009, 06:11 PM
Replies: 8
Views: 10,725
Posted By drgrcr
Check ICP pressure

If you access to a scan tool, you might want to check the ICP pressure
Showing results 1 to 14 of 14

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome