[alfaetreuf63]

Hello, and good morning well let me start with my problem I have a 96 F-250 powerstroke have two codes p0276 and P1275 now this codes go for injectors now I replace the two injectors and still having a problem, had a hard time to started but finally did and it ran good but the next day boom the same problems have no power and stalls a lot and gave me the two codes again,???????? need help please any body with ideas or a powerstroke mechanic /ubbthreads/images/graemlins/shrug.gif /ubbthreads/images/graemlins/shrug.gif /ubbthreads/images/graemlins/shrug.gif /ubbthreads/images/graemlins/shrug.gif /ubbthreads/images/graemlins/shocked.gif /ubbthreads/images/graemlins/shocked.gif /ubbthreads/images/graemlins/shocked.gifhelp.

 

[MADVAN]

Ran like crap from air in system until it blead out.
Did you change 6 and 8 injectors? Check wiring from idm all the way to the injectors. Possible valve cover gasket or connector.
The 1275 might come from the 0276.

Bill

 

[alfaetreuf63]

well I change the 5 and 6 injector and yes I have a new gasket for the driver side that I haven't change yet but I will do this now the codes are from two different sides which are the injectors that I change

 

[MADVAN]

You had stated same codes before and after.
Check wiring.
0276= #6 circuit low. (harness short), motor usually runs on 4cyl (FMEM mode)
1275= #1-8 high to low side open (open ckt,inj,idm), 1-8 inj fault
Driver side even #'s
Pass side odd #'s

You are throwing parts at it trying to repair.
Take some time to troubleshoot.

Bill

 

[alfaetreuf63]

Thank you I will give it a try, by the way whats the reading that I should look for?

 

[MADVAN]

Check here. ddog had pulled his hair out on this one.
http://forums.thedieselstop.com/ubbthrea...rue#Post3385419

Bill

 

[alfaetreuf63]

HA ha ha ha ha ha ha now I know how he felt thanks ha ha ha

 

[alfaetreuf63]

Well,well I broke the connector to the valve cover gasket ops, do you know where I can get one with out buying the whole wire harnnes.

 

[MADVAN]

Go to international.
They have the parts. Heard that some of the auto part suppliers are carrying them.
Someone will chime with part#'s.
I have to look them up.

Here you go (Joats page)
Valve Cover Harness Repair Kits (contains 4 hard shells w/seals, w/o terminals)
(Ford) F7TZ-14489-BA (94-96)
(Ford) F7TZ-14489-AA (97)
(International) 1830829C91 removal tool and Shells w/o pins
(International) 1661875C1 Pins
(International) 2501055C1 Pins with 6" wire
Valve Cover Pigtails with plug and wires, OBS
(Performance Specialties) 99288
(Ford) F4TZ-12A342-A
Valve cover harness replacement terminals:
Industry P/N 103935; Winzer Distributing (1-800-527-4126) selection number D52
Valve Cover Harness "Wedge" repair (not sure of years it fits or what it looks like)
(Ford) 2c3z-14a163-ab
Valve Cover Gasket (94-97)
(Ford) F4TZ-6584-A
(International) 1818350C2
Valve Cover Harness, under valve cover
(Ford) F4TZ-9D930-K (94-97)
(International) 1815923C92 (94-97)

Bill